Serving the design and engineering community for over 23 years.
3D-CAM, Inc. is AS 9100 Rev D & ISO 9001:2015 certified by BSI Management Systems America, Inc.
(818) 773-8777
ABS MOLDED
PHYSICAL PROPERTIES
| Density | 0.0368-0.0437 lb/in3 |
| Water Absorption | 0.05-1.8 % |
| Moisture Absorption at Equilibrium | 0.35-0.45 % |
| Water Absorption at Saturation | 0.3% |
| Linear Mold Shrinkage | 0.0024-0.0165 in/in |
| Melt Flow | 0.5-45 g/10 min |
MECHANICAL PROPERTIES
| Hardness, Rockwell R | 88-118 |
| Hardness, Shore D | 100 |
| Tensile Strength, Ultimate | 4320-9430 psi |
| Tensile Strength, Yield | 4290-9430 psi |
| Elongation @ break | 2-110 % |
| Elongation @ Yield | 1.7-6 % |
| Tensile Modulus | 260-464 ksi |
| Flexural Modulus | 233-856 ksi |
| Flexural Yield Strength | 6930-15500 psi |
| Compressive Yield Strength | 7690-12500 psi |
| Izod Impact, Notched | 0.749-12 ft-lb/in |
| Izod Impact, Unnotched | 20-NB |
| Izod Impact, Notched Low Temp | 0.899-4.01 ft-lb/in |
| Charpy Impact, Unnotched | 23.8-114 ft-lb/in2 |
| Charpy Impact, Notched Low Temp | 0.952-7.61 ft-lb/in2 |
| Charpy Impact, Unnotched Low Temp | 1.43-NB |
| Charpy Impact | 2.38-33.3 ft-lb/in2 |
| Gardner Impact | 1.33-14.6 ft-lb |
| Tensile Creep Modulus, 1 hour | 290000-363000 psi |
| Tensile Creep Modulus, 1000 hours | 167000-276000 psi |
ELECTRICAL PROPERTIES
| Electrical Resistivity | 1E+14-1E+16 ohm-cm |
| Dielectric Constant | 2.7-3.2 |
| Dielectric Constant, Low Frequency | 2.7-3.5 |
| Dielectric Strength | 399-864 kV/in |
| Dissipation Factor | 0.005-0.019 |
| Dissipatin Factor, Low Frequency | 0.005–0.016 |
| Surface Resistance | 1E+13-1E+15 ohm |
| Arc Resistance | 60-120 sec |
| Comparative Tracking Index | 400-600 V |
| Hot Wire Ignition, HWI | 7-15 sec |
| High Amp Arc Ignition, HAI | 15-120 arcs |
| High Voltage Arc-Tracking Rate, HVTR | 0.394-11.8 in/min |
THERMAL PROPERTIES
| CTE, linear 200 C | 36.1-83.3 µ in/in-°F |
| Heat Capacity | 0.468-0.509 BTU/lb-°F |
| Thermal Conductivity | 0.888-1.32 BTU-in/hr-ft²-°F |
| Maximum Service Temperature, Air | 140-223°F |
| Deflection Temperature at 0.46 MPa | 154-284°F |
| Deflection Temperature at 1.8 MPa | 165-428°F |
| Vicat Softening Point | 189-284°F |
| Glass Temperature | 225-239°F |
| UL RTI, Electrical | 140-176°F |
| UL RTI, Mechanical with Impact | 140-176°F |
| UL RTI, Mechanical without Impact | 140-176°F |
| Flammability, UL94 | HB |
| Oxygen Index | 19 % |
OPTICAL PROPERTIES
| Gloss | 40-96 % |
PROCESSING PROPERTIES
| Processing Temperature | 399-500°F |
| Rear Barrel Temperature | 482°F |
| Middle Barrel Temperatue | 482°F |
| Front Barrel Temperature | 482°F |
| Nozzle Temperature | 482°F |
| Mold Temperature | 109-149°F |
| Drying Temperature | 171-205°F |
HANDLING PROPERTIES
| Mixed Viscosity(cps) | 15,500 |
| Work Life@ 770F(250C) | 60 minutes |
| Demold Time@ 750-80F(240-27°C) | 16-24 hours |